Why do it yourself?
At Luminis Films, all our products are accessible to the greatest number of people in terms of ease of application. You can apply your window film or decorative coating yourself: it couldn't be easier!
The advantages are numerous, so don't wait any longer to try the adventure and bring all your projects to life!
-
Time saving and flexibility
Project completion at any time. You decide when you want to carry out your project, You do not need to go through our service to make an appointment with a fitter.
-
Less expensive project
Save money by installing your own film or covering and and offer yourself a decoration or renovation project at a lower cost!
-
Do-it-yourself satisfaction
Do you have the soul of a handyman? Be proud of your Luminis Films production by doing it yourself, at your own pace!
Would you like to place an order?
Visit our Cutting Service page to find out how!
Our tips for successful installation of :
Successful application of adhesive film:
When applying your self-adhesive window film, you must ensure that you follow all the steps in the instructions and also watch the tutorial videos on our in the application instructions and also watch the tutorial videos on our Youtube channel which will allow you to Youtube channel which will allow you to put images on each step.
Luminis Films Tip
Do small bubbles appear after application? Don't worry, they will disappear once the film has dried completely.
Downloadable leaflet
Download instructions Adhesive filmstep 01: Prepare your installation
Preparing the substrate is the most important step in the successful installation of your adhesive film. To do this, gather the necessary material proposed by Luminis Films: the KITbat installation material kit then clean the glass properly, if necessary use a scraper to remove all impurities and wipe and wipe with a clean cloth. You can now prepare the film for cutting if required.
step 02: put the film on the window
First of all, you need to prepare a soapy water solution and spray it generously onto the glass. Remove the protective film while also spraying the adhesive side with soapy water and then position the film.
step 03: Finish the application
Smooth and roll the film to remove the soapy water, always from the inside out. If necessary, cut off the excess film, then roll it again, pressing lightly to remove the last bubbles. Finally, wipe with a dry cloth.
For more information •••
See our guide for some installation tips:
Successful application of window filmSuccessful application of electrostatic film
With electrostatic, you can repeat the application as many times as you like, so it is the most recommended solution if the application of a window film seems too complicated! Here again, preparation is the most important step.
Luminis Films Tip
To reuse your heat protection film year after year, make sure you clean it after each summer and store it in a clean, dry place.
Downloadable leaflet
Download instructions Electrostatic filmstep 01: Prepare your installation
It is very important to prepare your glass surface before applying your film, It is this main step that will guarantee the desired result! To do this, gather the necessary material proposed by Luminis Films: the KITbat installation material kit then clean the glass properly, if necessary use a scraper to remove all the impurities and wipe remove all impurities and wipe with a clean cloth. Only when your surface is When the surface is clean, you can proceed to the next step.
step 02: Apply the film to the glass
To carry out the second step, be sure to prepare a soapy water-based solution spray it generously on the glass and on the adhesive part of the film once the protective film has been removed. Then place the film on the glass and start taping. If you see that the film is not installed properly, do not hesitate to peel it off, apply soapy water and reapply it to the glass.
step 03: Finish the application
Smooth and roll the film to remove the soapy water, always from the inside to the outside. Remove the excess film with a cutter if necessary, being careful with your windows, and press again without hesitating to press slightly if there are still small bubbles. With a clean, dry cloth, wipe off the film to finish the application.
For more information •••
Still not sure whether to use adhesive or electrostatic window film? To help you out, check out this guide:
An adhesive film or electrostatic film?Successfully applying scratch film
An ideal seasonal solution for skylights or verandas, solar scratch film is an essential for protection from the summer heat, especially if you are south-facing!

Luminis Films Tip
For vertical walls: put a scratch every 50 cm.
For sloping walls (e.g. veranda roof or velux): put a scratch every 30 cm.
Downloadable leaflet
Download instructions Film scratchstep 01: Prepare your installation
Firstly, clean the frame and the interior glazing of the skylight or window to be fitted thoroughly, then check the dimensions of the film: it must be slightly larger than the window in order to be able to be fixed to the frame using the Velcro fasteners.
step 02: Apply the scratches
First apply one side of the scratch pads directly to the outer corners of the film and repeat the process on the inner frame of the mirrored window with the scratch pads already placed on the film so that they stick together. Then remove the protector from both sides of the Velcro and hang them on top of each other, making sure to stretch the film.
step 03: Finish the installation
Once installed, your brand new scratch film will stay in place for as long as you like! At the end of the summer, you can remove it if you wish and store it in a clean, dry place for next year!
Successful installation of your adhesive coating
With its thickness, the adhesive coating will be able to cover many non-porous surfaces while masking small roughnesses. However, it is important to ensure that the surface to be covered is properly prepared and that a flask is used.
Luminis Films Tip
Don't have a heat gun to thermoform your decorative adhesive? Use your hair dryer instead!
Downloadable leaflet
Download instructions Adhesive coatingstep 01: Prepare your installation
Make sure you have the right equipment for successful installation. The VO216 installation kit installation kit contains everything you need for a successful application! You can also use the isopropyl alcohol solution to thoroughly clean and degrease the surface to be fitted: this step is essential.
step 02: Apply the coating to the surface
Make your cuts if necessary and gently begin the dry application of your adhesive using a 45° angle squeegee to remove air. Squeeze firmly from the centre outwards to expel air and bond the coating to the application surface. If you are applying the adhesive to a curved surface, feel free to thermoform it (if possible) using a heat gun. This will soften the coating and make it more pliable so that it will take the desired shape.
step 03: Finish the installation
Puncture any bubbles with a small point and tap again to complete the installation.
For more information •••
Have you successfully applied your decorative coating? Find out in this guide how to maintain it on a daily basis!
How to care for your Luminis Films deco tapeSuccessful application of solar lacquer
Very popular in workshops or warehouses, solar lacquer is an excellent way of cooling the air inside when the sun is beating down on the roof, which is often made of Plexiglas sheets.

Luminis Films Tip
For corrugated surfaces, make sure to apply from the bottom up and apply a final veil to the corrugated areas (from top to bottom).
Downloadable leaflet
Download manual Solar lacquerstep 01: Prepare your installation
Thoroughly wash the surface with e.g. washing powder until the result is to obtain a result without oily or greasy traces. If necessary, scrape off any foam and If necessary, scrape off any foam and wait for it to dry completely before proceeding to the next step.
step 02: Apply the lacquer
There are 2 ways to apply the sun protection lacquer. A) With a short-haired roller: make sure you apply 2 thin, even coats with a drying time of 1 hour between each. B) With a spray gun (compressor or electric): stir the can of lacquer before application, use a nozzle of about 0.8 mm and spray evenly 30 cm from the surface. For a satisfactory result, favour 3 passes, criss-crossing the direction of spraying, with fairly light veils so as not to create over-thicknesses.
step 03: Finish the installation
Then you just have to wait for the solar paint to dry completely, it takes between 15 minutes and 2 hours depending on the weather conditions. The solar paint hardens completely between 2 and 6 hours after the last application.
For more information •••
Would you like to see the result of a solar lacquer application? Check out this client's achievement:
Solar lacquer: the ideal option for a workshop
A doubt? A question?
Don't wait any longer to contact our team of advisors!
00 33 472 41 06 60Monday to Friday from 8am to 6pm
(price of a local call)
Send a message